Part one covered measurements (Trukk vs. Taurox), most of the cab, the chassis, and the axles and wheels. As before, the foundation of, and inspiration for, this conversion — my first — is the excellent work done by Hobbyistgirl on her Taurox Trukk conversion. I’ve diverged a bit from her build, and I’m diverging from it more in this second post.
This is the final second in a five-post series documenting this Trukk. Assembly started in part one, the color guide is in part three, a few WIP shots are in part four, and the finished product is in part five.
I want my converted Trukk to still look ramshackle (an actual game mechanic that means you can only do so much damage to the vehicle, as it’s so full of holes and gaps already), despite the pristine armored compartment for the driver. That starts with the engine compartment, which I’ve built around the idea that my Meks chopped off the front end of the Taurox and slapped in a big-block engine with a blower.
Let’s get choppin’
First, I shimmed the spot where the engine will sit to make it the right height.
Then I cut and weathered the Taurox engine compartment panels and glued them in place. I used the Taurox exhaust pipes on both sides; on the left side, they’re intact. I also used the Taurox light on the left side, since I like asymmetry in my Ork stuff.
I didn’t notice the cool NOS attachment that’s supposed to go on the left side of the engine until it was too late; I’ve already partially blocked that spot. (No worries, though; I trimmed it a bit and jammed it on there later.)
I covered the unsightly gap, and the shim, with a bit of trimmed-down Trukk scrap.
Then I roughed up the grill from the Taurox and stuck it to the engine, alone with the Trukk bumper (attached exactly as the kit intends, since I left the front of the Trukk chassis intact in part one).
I like the idea of my Orks being like, “Oi, let’s put dis bit back, hurr hurr,” and then sticking the grill back on because it’s funny.
Next I added the bed sides, armor, and roll bars per the Trukk instructions.
DakkaDakka lists the Trukk’s height as 3″, and my converted Trukk is already 3″ high at the roll bars. I wasn’t sure I liked the boarding ramps, so this is a great excused to not use them as they’d make the Trukk much too tall. So instead I chopped them to roughly match the height of the bed sides.
Next I added the turret, gunner, and Wreckin’ Ball. This pushed my Trukk up to about 3 1/2″ tall, which doesn’t seem like a huge deal. I forgot to take a photo of that stage, but I built those bits just like the stock Trukk; the Trukk turret is exactly the same diameter as the hole in the Taurox roof.
After that, it was time for greeblies, covering up holes, creating new holes, and weathering the Taurox bits so they don’t look too pretty. I also added a Squig, because I love Squigs and empty truck beds on miniatures look weird, and I stuck a sign with the Ork glyph for “danger” just below him.
This was a really fun conversion, and a good choice for my first. Thanks to Hobbyistgirl’s WIP pics and guide, I had the confidence to give it a shot and a basis for diverging from her build where I wanted to achieve a different effect.
It’s about 1/2″ taller than the stock Trukk, but it’s the same width and length. The silhouette is roughly the same, although the cab is certainly more solid. I tried to make that section look as ramshackle as possible while still being recognizably a Taurox Prime. All in all, I did a pretty good job of hitting all of my initial design goals — not perfect, but I’m digging it.
After a bit of thought, I’m naming this Trukk Da Fancy Wun.